B&O's 2-6-6-2 Locomotives: Specs, Roster, Photos

Published: April 7, 2025

Like most large railroads the B&O acquired some of its steam locomotives by purchasing smaller systems.

The largest included a batch of 2-6-6-2s it picked up from the Buffalo, Rochester & Pittsburgh during the early 1930s which was also one of the largest types that railroad ever owned.

These somewhat antiquated and older Prairie Mallets were in service on the BR&P; for less than twenty years (some saw fewer than ten years) of service before the B&O takeover, which continued to operate them in their home region of Pennsylvania and New York until all were retired by the 1950s.

Interestingly, the B&O modified the steamers only slightly under its ownership, predominantly leaving them as built for the BR&P. Today, none survive.

The Buffalo, Rochester & Pittsburgh was medium sized, western Pennsylvania carrier that predominantly handled coal from that region.

While the BR&P also reached Buffalo and Rochester, New York it was acquired by the B&O in the hopes of eventually establishing a direct corridor to New York under President Daniel Willard's administration.

Baltimore & Ohio 2-6-6-2 #7502 (KK-4) is seen here in Bradford, Pennsylvania on the former Buffalo, Rochester & Pittsburgh during 1947. Note the air tank atop the boiler. This locomotive was built as Buffalo, Rochester & Pittsburgh #702 (note the new number patch on the cab).

While the B&O used many types of large, articulated steamers it never used the 2-6-6-2 design in great numbers except those it either received from the BR&P or a few it had built for testing purposes. The 2-6-6-2 was one of the earliest articulated steamers to enter service.

Its inspiration came from the B&O's pioneering 0-6-6-0 "Old Maude" of 1904 as the Great Northern slightly improved upon the design and ordered five 2-6-6-2s in 1906 from the Burnham, Williams & Company.

Many from this era, including the GN's were built as Mallets and found perhaps as much success by private logging companies as they did on major railroads with names like Simpson Logging, Clover Valley Lumber, and Saginaw Timber all owning at least one.

Buffalo, Rochester & Pittsburgh

During 1914 the Buffalo, Rochester & Pittsburgh ordered a batch of 2-6-6-2s from the American Locomotive Company.

It intended to use these Mallets in heavy drag service, moving coal trains and other heavy freights over its stiff grades in northern Pennsylvania and western New York. The BR&P was a smaller road that dated to the late 1860s, built to haul coal out of this region.

While the system was never able to reach Pittsburgh via its own rails it did reach Buffalo and Rochester, New York and as far south as Walston, Pennsylvania.

Along with a fleet of 2-8-8-2s, the 2-6-6-2s were the BR&P's largest locomotives; in all it acquired 55 examples between 1914 and 1923, numbered 700-754, and listed simply as Class LL.

According to David Mainey's book Baltimore & Ohio Steam In Color the Mallets were an older design (compound steam was losing its appeal by the World War I era and into the 1920s) and had remained virtually unchanged over during its ten year production run featuring large, bulbous low-pressure cylinders and old-style slide valves.

Modifications

Most railroads, especially when purchasing a wheel arrangement over such a long time period, had additions or improvements incorporated into them.

However, in this case the BR&P's the 2-6-6-2s were practically the same aside from subtle differences including weight variations and the batch of fifteen (under the B&O these were listed as Class KK-4c) that used Southern valve gear.

In 1932 the Baltimore & Ohio acquired the railroad giving it access to the region's coal fields as well as Buffalo/Rochester.

After the takeover the B&O reclassified the 2-6-6-2s as KK-4a through KK-4d, numbering them 7500-7554. Mr. Mainey's book goes on to state that under B&O's ownership little changed on the locomotives except for their new designation.

There was only one that saw any significant upgrades, #7518. In 1949 the B&O overhauled the steamer with new low and high pressure cylinders using piston valve gears, a cast frame, chassis lubrication, and slightly larger drivers (as built they featured 57-inch drivers).

Specifications

Model	Builder	Road Number(s)	Date Built	Disposition
Class KK-1	Baldwin	7400	1930	Retired, 1953
Class KK-2	Baldwin	7450	1930	Retired, 1953
Class KK-4	Alco-Schenectady	7500-7504	1914	Retired, 1953
Class KK-4a	Alco-Brooks	7505-7509	1917	Retired, 1953
Class KK-4b	Alco-Brooks	7510-7525	1918	Retired, 1953
Class KK-4c	Alco-Brooks	7526-7540	1918	Retired, 1953
Class KK-4d	Alco-Brooks	7541-7554	1923	Retired, 1953
Class KK-5	B&O	7518	1949	Retired, 1953

These changes along with some slight cosmetic improvements (such as the removal of the air tank atop the boiler and the addition of air pumps on the pilot deck) allowed #7518 to stand out among its other peers.

From a visual standpoint it was certainly a more appealing locomotive than the others. Interestingly, the Class KK-4's were one of the B&O's only large, articulated designs that did not see action on the West End.

After the BR&P takeover the railroad left them in their home territory along the Buffalo Division where they spent their days continuing to work heavy freights over the notorious grades in this region.

Mr. Mainey's book provides a nice selection of color photos depicting the 2-6-6-2s in action there such as at Bradford, Pennsylvania and scenes of the engine terminal in East Salamanca, New York.

Retirement

Somewhat unknown within the fleet were two additional examples, Class KK-1 #7400 and Class KK-2 #7450. Manufactured much later than the former BR&P units they were built by the Baldwin Locomotive Works in 1930.

According to SteamLocomotive.com their purpose was "...to compare the Emerson watertube firebox to a conventional locomotive." They were somewhat larger and more powerful, sporting additional tractive effort and bigger drivers.

Both remained in service until the early 1950s when they were finally retired. Incredibly, despite their use of compound steam and antiquated design the B&O kept most of the Class KK-4's in service, also until the early 1950s. Unfortunately, no examples were preserved.

Facebook X Pinterest Tumblr Reddit WhatsApp Messenger